Here you go! Have fun! If you have any questions, send an email to [email protected]
1) 12” x 12” piece of ½”- thick foam board
2) #13 knitting needle
3)
4-7/8” half-ball of florist’s foam (or something to stick the knitting
needle into in case you make the hole too big in the shaker box; if you
are careful when you make the hole, you might not need this)
4) 2 sizes of round dishes for tracing; one with a 10” diameter, the other with a 12” diameter
5) 6” tall x 5” round shaker box with lid
6) this is the UPC code for the shaker box so you know the correct size to buy
7) utility knife
8) mod podge
1) Trace the 10” plate onto the foam board
2) Cut out circle with utility knife (don’t worry if it looks raggedy; you are going to be covering the ugly part with paper)
3) Draw a little circle in the center
4) Carefully poke a hole in the center with the tip of the knitting needle; remove the needle and set needle aside for later use
1)
Drill or punch a hole into the center of the lid to the shaker box.
Make sure you make the hole just big enough so that you can insert the
knitting needle. (Be careful not to make the hole too big.)
2) Cut two strips of decorative paper 12” x 6” and adhere to shaker box with mod podge
3) Look how pretty!
4)
Cut two strips of decorative paper 12” x 1” and adhere to the side of
the shaker box lid (you don’t have to put any paper on the top of the
lid)
1)
Cut two strips of decorative paper 12” x ¾” and adhere to the side of
the table top (it’s not going to look very pretty, but that’s okay. You
are going to hide it later)
2) Put some Mod Podge on the top of the shaker box lid
3) Attach the table top to the shaker box lid, making sure to line up the holes
4) Allow to dry
Trace the 12” plate onto a piece of decorative paper and cut out. Then
trace the 10” plate onto the 12” circle that you just cut out.
2) Cut a fringe up to the trace-line around the entire diameter of the 12” circle
3) Punch a hole in the center and adhere to the table top
That’s it for the table. Let’s move on to the umbrella.
1) Die-cut six large pennants. Cut 2 each of 3 different paper patterns
2) Cut off the side scallops, leaving the top two scallops on each side, as shown
3) Die-cut six large cardboard pennants
4) Cut off the entire bottom and the scallops on the cardboard pieces as shown
5) Die-cut six large pennants from the plain cardstock
6) Glue the decorative-paper pennants onto the plain-paper pennants as shown
1) Fold up scallop edges along perforated lines and apply mini glue dots to scallops
2) Attach scallop edges of umbrella pieces together
3) This is what it will start to look like as you attach the pieces to each other
4) This is what it will look like underneath
5 to 7) Continue attaching all umbrella pieces, making sure to rotate colors
2)
To reinforce the umbrella, we are going to use the cardboard pennant
pieces. Apply double-sided tape to each cardboard pennant piece. Adhere
each cardboard piece to the underside of the umbrella so that one half
of the cardboard piece is attached to one half of an umbrella piece.
3) Line up the score line of the cardboard piece with the place where the umbrella pieces are attached
4) Continue until all cardboard pieces are attached
5) Apply a couple of pop-up glue dots (or another very strong gummy adhesive) to the top of the knitting needle
6) Stick the knitting needle onto the center of the umbrella, insert the needle into the table top, and you’re done! Whew!
For
the place settings, the possibilities are endless. I used plastic
shot-glasses for the cups and used some die-cut flowers from the
“Baskets and Blooms” die for decorations.
